pedro polyskin sides and back che ne pensi?

[surferste]

pedro cosa ne pensi della scelta del polyskin x sides and back larghezza 1 pollice?

usato con la colla dovrebbe semplificare applicazione e pulizia, e in piu non si sente all tatto.

 

grazie

[Visitatore gabriele5]

PENSO VADA BENE...STO PARTENDO PER L'ESTERO(BERLINO)QUINDI PER UN Pò DI GIORNI NON POTRò PARTECIPARE AL SITO ...SALUTI E BUON WEEK END A TUTTI

[surferste]

x prossimo ordine base 64#, front 18#, densita 80 front, 90 resto.

rimane da verificare quando dev essere grosso il polyskin x tenere abbastanza con la colla anche sott'acqua.

hollywood dice che non va bene x un taglio corto xche si vede.ma corto quanto?...

xxx

unregistered user

02-19-03, 06:07 PM (EST)

 

"polyskin for sides and back"

 

a friend of mine has got a polyskin unit, and he's doing just fine with that because he uses glue so that it is undetectable to the touch, and it is very easy to clean, 5 minutes with solvent.

so we were thinking about an all lace system(18#front,64#base), and a large polyskin aerea for sides and back to attach with glue.

what do you think about it?

 

 

 

 

 

Alert | IP Printer-friendly page | Edit | Reply | Reply With Quote | Top

 

 

Hollywood

unregistered user

02-20-03, 12:11 PM (EST)

 

1. "RE: polyskin for sides and back"

In response to message #0

 

>a friend of mine has got a polyskin unit, and he's doing

>just fine with that because he uses glue so that it is

>undetectable to the touch, and it is very easy to clean, 5

>minutes with solvent.

>

>so we were thinking about an all lace

>system(18#front,64#base), and a large polyskin aerea for

>sides and back to attach with glue.

>what do you think about it?

Hey xxx,

 

On my first CoolPiece order, I did basically the same thing. What I found was...for me...that the polyskin perimeter was visible on a short cut. If you plan on going short (which I though is what you said you wanted to do) then I don't believe polyskin would be the right choice.

 

On my next order, I'm thinking of either having them double the 64# around the perimeter or seeing if the 3# is strong enough just to leave at the edge. My density will be 100% on top because I want to use gel and/or wax for that messy "bedhead" type look without showing a lot of scalp. So I that way I can use tape to apply and not worry about it being visible from above.

 

Bottom line is, tell Jeffrey exactly what you want to do in terms of your order and the style you want to wear and see what he recommends. Good luck!

 

Hollywood

 

 

 

 

Alert | IP Printer-friendly page | Edit | Reply | Reply With Quote | Top

 

 

xxx

unregistered user

02-20-03, 01:48 PM (EST)

 

2. "RE: polyskin for sides and back"

In response to message #1

 

i have 90% density and planning a 2" long haircut, does polyskin show in this case?

is the attachement strong enough on a 1" polyskin sides and back, even for showering with hair on?

thank you very much hollywood

 

by the way is 3# detactable to eyes and touch with 90% density?

[surferste]

xxx

unregistered user

02-20-03, 09:51 AM (EST)

 

"polyskin sides and back"

 

is that enough 1" perimeter with polyskin sides and back to attach system with glue and even swim?

thanx

 

 

 

 

Alert | IP Printer-friendly page | Edit | Reply | Reply With Quote | Top

 

 

Hairwearer

unregistered user

02-20-03, 11:51 AM (EST)

 

1. "RE: polyskin sides and back"

In response to message #0

 

That's what i have to. it's perfect, considering the fact that much of the tapes you can use to attach the sides and back are one inch or less

 

 

 

Alert | IP Printer-friendly page | Edit | Reply | Reply With Quote | Top

 

 

xxx

unregistered user

02-20-03, 03:43 PM (EST)

 

2. "RE: polyskin sides and back"

In response to message #1

 

have you tried coolpiece polyskins?are they detectable to sight (shine) and sight?

thanx